Thanks for downloading!
We'd love to hear from you if the print was successful.
Bidet with Replaceable Nozzel
Bidet print flat, heat form with hair dryer
For your home
Creative Commons Attribution Noncommercial Share Alike
Commercial use is not allowed, you must attribute the creator, you may remix this work and the remixed work should be made available under this license.
Attribution
Art from Home depot
Description
!!!BUILT FROM OFF THE SHELF PARTS - SOURCED AT HOME DEPOT!!!
Worried about TP shortage?
Just want a cleaner experience?
Totally SOLD OUT of Bidets?
Print your own Bidet!!! The print flat and heat form design makes installation and assembly a breeze. All parts sourced from local hardware stores.
IMPORTANT!!!!
there are 2 designs, one specifically for my easy clean toilet seat so I didn't need to unscrew anything, and another that should work with any lid (requires removing screws). feel free to adjust design in blender/etc.
BOM:
Got help with this from Home Depot Employee Art! Thanks Art!
Faucet to Diverter supply line - shown in blue
Supply line to diverter coupling required - green
Shower head diverter for switch - light purple
Diverter to toilet tank connection, you'll need new one!!! - orange
Line from diverter to bidet, Coupler: needs plumbers tape, wrap in direct of thread tightening - red
PushFit - yellow
Line to bidet nozzel - bottom edge of image
Note: Adjust as available parts 5 through 7, the following parts were the only ones available at the hardware store I visited, you could use a smaller push fit and supply line if the appropriate adapters are available
Additional tools and resources:
- Plumbers tape: https://www.homedepot.com/p/Harvey-1-2-in-x-260-in-PTFE-Tape-0178502/202280370
- Zip Ties: https://www.homedepot.com/p/Commercial-Electric-Assorted-Cable-Ties-650-Pack-4-8-11in-UV-tie/302366855
- Plumbers Tape
- Crescent wrench
Materials and methods
Bracket Installation:
1. Remove toilet seat
2. place bidet bracket over holes
3. replace seat on top of bracket and screw down
4. attach hose to nozzle, use zip tie to secure (make as tight as possible to eliminate leaks)
5. attach nozzle to bracket with zip tie
6. heat form bracket in place with hair dryer, being careful only to warm middle section where bending is required: heat, bend, cool, and repeat as needed
Bill Of Materials as shown:
Got help with this from Home Depot Employee Art! Thanks Art!
1. [Faucet to Diverter supply line](https://www.homedepot.com/p/BrassCraft-3-8-in-Compression-x-1-2-in-FIP-x-12-in-Braided-Polymer-Faucet-Connector-B1-12A-F/100068479) - shown in blue
2. [Supply line to diverter coupling required](https://www.homedepot.com/p/Everbilt-1-2-in-MIP-x-Close-Lead-Free-Brass-Pipe-Nipple-Fitting-802679/207176628) - green
3. [Shower head diverter for switch](https://www.homedepot.com/p/Glacier-Bay-Shower-Diverter-in-Chrome-3075-541/204511170) - light purple
4. [Diverter to toilet tank connection, you'll need new one!!!](https://www.homedepot.com/p/1-2-in-IPS-x-7-8-in-BC-x-20-in-Braided-Stainless-Steel-Toilet-Supply-Line-7233-20-12-1/203082389) - orange
***Note: Adjust as available, the following parts were the only ones available at the hardware store I visited, you could use a smaller push fit and supply line if the appropriate adapters are available***
5 . [Line from diverter to bidet, Coupler: needs plumbers tape, wrap in direct of thread tightening](https://www.homedepot.com/p/Everbilt-1-2-in-FIP-Lead-Free-Brass-Pipe-Coupling-Fitting-802209/300096268) - red
6 - [PushFit](https://www.homedepot.com/p/John-Guest-3-8-in-O-D-x-1-2-in-MIP-NPTF-Polypropylene-Push-to-Connect-Adapter-Fitting-803229/300753472) - yellow
7. [Line to bidet nozzel](https://www.homedepot.com/p/Everbilt-3-8-in-O-D-x-1-4-in-I-D-x-20-ft-Clear-PVC-Vinyl-Tubing-702165/207144345) - bottom edge of image
###Additional tools and resources:
- Plumbers tape: https://www.homedepot.com/p/Harvey-1-2-in-x-260-in-PTFE-Tape-0178502/202280370
- Zip Ties: https://www.homedepot.com/p/Commercial-Electric-Assorted-Cable-Ties-650-Pack-4-8-11in-UV-tie/302366855
- Plumbers Tape
- Crescent wrench
Documents
Edit in 3dslash
Issues
Issues are used to track todos, bugs or requests. To get started, you could create an issue.
Comments
claybson Flores added this to the novidade collection ago
BarronEric added this to the good stuff collection ago
Everett Bromwich added this to the home improvement collection ago
Kim Watson added this to the Things to make collection ago
killtron4000 published this design ago