Piezas

Creative Commons Attribution Share Alike

Commercial use is allowed, you must attribute the creator, you may remix this work and the remixed work should be made available under this license.

Learn more or download attribution tags

Description

I have designed these pieces to make a tailor made shoemaker. The pieces are designed for rods of 8mm in diameter. The shoemaker that he made has dimensions of about 70 cm wide by 50 cm of althacerlo with iron rod aluminum. And it did with 8mm beech rod. Slightly bend, it would be advisable for these dimensions to make with the aluminum rod of iron, since it is more resistant.
I have also calculated the scaling by rods of other dimensions which are as follows:

IRONS
For rods of 4.2 mm resize in curing to 52.5%
For 6mm rods resize in curing 75%
For rods of 8 mm resize in cure to 100%
For rods of 10 mm resize in cure to 125%
For 12 mm rods resize in cure to 150%
For rods of 14 mm resize in cure to 175%
For rods of 16 mm resize in curing to 200%

WOODS
For rods of 3 mm resize in curing to 37.5%
For rods of 4 mm resize in curing to 50%
For 5 mm rods resize in curing to 62.5%
For 6mm rods resize in curing 75%
For rods of 8 mm resize in cure to 100%
For rods of 10 mm resize in cure to 125%
For 12 mm rods resize in cure to 150%
For rods of 14 mm resize in cure to 175%
For rods of 16 mm resize in curing to 200%

These equivalences are calculated with a simple rule of three, I have not printed the pieces, so before preparing a project it would be best to make some pieces to confirm the measurements.

I have also included a stand for shelves in which on one side would stick the shelf and on the other would be attached to the rod with two flanges.

I hope they are useful.
If you have any questions, feel free to receive comments

He diseñado estas piezas para hacer un zapatero a medida. Las piezas están pensadas para varillas de 8mm de diámetro. El zapatero que he hecho tiene unas dimensiones de unos 70 cm de ancho por 50 cm de alto hacerlo con varilla de hierro de aluminio. Yo lo hice con varilla de la haya de 8m m. Pandea un poco, sería aconsejable para estas dimensiones hacerlo con la varilla de hierro del aluminio, ya que es más resitente.
También he calculado el escalado por varillas de otras dimensiones que son los siguientes:

HIERROS
Para varillas de 4,2 mm redimensionar en cura al 52,5%
Para varillas de 6 mm redimensionar en cura 75%
Para varillas de 8 mm redimensionar en cura al 100%
Para varillas de 10 mm redimensionar en cura al 125%
Para varillas de 12 mm redimensionar en cura al 150%
Para varillas de 14 mm redimensionar en cura al 175%
Para varillas de 16 mm redimensionar en cura al 200%

MADERAS
Para varillas de 3 mm redimensionar en cura al 37,5%
Para varillas de 4 mm redimensionar en cura al 50%
Para varillas de 5 mm redimensionar en cura al 62,5%
Para varillas de 6 mm redimensionar en cura 75%
Para varillas de 8 mm redimensionar en cura al 100%
Para varillas de 10 mm redimensionar en cura al 125%
Para varillas de 12 mm redimensionar en cura al 150%
Para varillas de 14 mm redimensionar en cura al 175%
Para varillas de 16 mm redimensionar en cura al 200%

Estas equivalencias están calculadas con una simple regla de tres, no he impreso las piezas, así que antes de preparar un proyecto lo mejor sería que hicierais unas piezas para confirmar las medidas.

También he incluido un soporte para baldas en el que por una cara se pegaría la balda y por la otra se sujetaría a la varilla con dos bridas.

Espero que sirven de utilidad.
Para cualquier pregunta hecedmela llegar, estar encantado de recibir comentarios

Materials and methods

These equivalences are calculated with a simple rule of three, I have not printed the pieces, so before preparing a project it would be best to make some pieces to confirm the measurements.

I have also included a stand for shelves in which on one side would stick the shelf and on the other would be attached to the rod with two flanges.

I hope they are useful.
If you have any questions, feel free to receive comments